文档视界 最新最全的文档下载
当前位置:文档视界 > 齿轮参数中英文对照

齿轮参数中英文对照

齿轮参数中英文对照 SANY标准化小组 #QS8QHH-HHGX8Q8-GNHHJ8-HHMHGN#

EXTERNAL SPUR GEAR DATA(外圆柱齿轮参数)

manufacturing data(制造参数)

part number(零件号)

tooth form(齿面)

gear type(齿轮类型)

number of teeth(齿数)

normal module(法向模数)

normal pressure angle (at ref circle)法向压力角(在分度圆上)

helix angle (at ref circle)螺旋角(在分度圆上)

helical lead(螺旋导程)

hand of helix(旋向)

reference face width(参考齿宽)

outside diameter(齿顶圆直径)

chamfer diameter(倒圆直径)

reference(pitch)circle diameter(分度圆直径)或节圆

start of active profile diameter有效渐开线起始圆直径

form diameter 展成直径

root diameter齿根圆直径

base circle diameter基圆直径

whole depth全齿高

normal circular tooth thickness (at reference circle)法向弧齿厚(在分度圆上)root type齿根形式

root fillet radius 齿根圆角半径

lead crown齿向鼓形

HOB DATA滚刀参数

pressure angle压力角

tooth thickness at reference line分圆齿厚

protuberance凸角

tip radius齿顶圆半径

reference part number 零件号

INSPECTION DATA检验数据

profile tolerance and modifications齿形公差和修形

profile hollow齿形中凹

refernce pitch circle runout节圆跳动

pitch variation齿距偏差

lead variation齿向偏差

lead hollow齿向中凹

profile surface finish渐开线齿面精加工

ball diameter量球直径

dimension over two balls in same plane跨棒距

REFERENCE DATA-MATING GEAR对啮齿的参考参数

normal center distance 中心距

mating gear part number对啮齿轮零件号

mumber of teeth on mating gear对啮轮齿数

backlash (nominal CD ,ROOM TEMP)侧隙(法线方向,室温)

general notes(通用技术要求)

not scale drawing(不要在图上量取尺寸)

surfaces corners and edges must be free from burrs

and sharp edges-break MM MAX(所有面,角和边不能有毛刺,锐边倒钝不超过

otherwise stated(除非特别注明,否则)

dimensions and tolerance are in millimeters per

Chinese standard(所有以毫米为单位的尺寸和公差均按中国标准)

surface finishes to be micrometer or better(所有表面粗糙度不应低于

dimension are finished dimensions;no allowance has been

made for any change in maximum or least material condition

due to heat treatment(所有尺寸均为最终尺寸;热处理导致的最大或最小实体条件的变化不应超出允差)

D linear dimensions to be +/- MM(线性尺寸偏差为+/- MM)

E angular dimensions to be +/- o(角度尺寸偏差为+/- o)

part number as shown(如图作零件号)

serial number as shown(如图作系列号)

treatment to be applied to all surfaces(整体热处理)

gear notes(齿轮技术要求)

not grind roots and fillets after heat treatment(热处理后不得磨及齿根和圆角)

steps or grooves permissible in root and fillet region after

honing or grinding(珩磨后,齿根和圆角区域不允许有台阶或凹痕)

tolerance based upon floating band fit(齿形误差应以公差带为计)

must be free from grind burns and tempering(齿面不得烧伤)

line runout and other tooth tolerances are with respect to

datum A(节圆跳动和其它齿轮公差均以基准A为测量基准)

tolerance to be measured between form and chamfer(齿形误差应由渐开线起始(或终止)圆测量至齿顶倒角)

hardness must be achieved in tooth root and fillet region(齿根和圆角处的硬度不得低于硬度下差)

radius tangent to profile not to extend above form diameter(齿根圆角要与齿面相切,而且不能超过渐开线起始(或终止)圆直径。

not thru harden tooth tips(齿尖不得淬透)

齿轮基本术语

齿轮 Toothed gear;Gear

齿面 Tooth flank

长幅内摆线 Prolate hypocycloid 齿轮副 Gear pair

右侧齿面 Right flank 短幅内摆线 Curtate hypocycloid

平行轴齿轮副 Gear pair with parallel axes

左侧齿面 Left flank

渐开线 Involute;Involute to a circle 相交轴齿轮副 Gear pair with intersecting axes

同侧齿面 Corresponding flank

延伸渐开线 Prolate involute

齿轮系 Train of gears

异侧齿面 Opposite flank

缩短渐开线 Curtate involute

行星齿轮系 Planetary gear train

工作齿面 Working flank

球面渐开线 Spherical involute

齿轮传动 Gear drive;Gear transmission 非工作齿面 Non-working flank

渐开螺旋面 Involute helicoid

配对齿轮 Mating gears

相啮齿面 Mating flank

阿基米德螺旋面 Screw helicoid

小齿轮 Pinion

共轭齿面 Conjugate flank

球面渐开螺旋面 Spherical involute

helicoid

大齿轮 Wheel;Gear

可用齿面 Usable flank

圆环面 Toroid

主动齿轮 Driving gear

有效齿面 Active flank

圆环面的母圈 Generant of the toroit

从动齿轮 Driven gear

上齿面 Addendum flank

圆环面的中性圈 Middle circle of the

toroid

行星齿轮 Planet gear

下齿面 Dedendum flank

圆环面的中间平面 Middle-plane of the toroid

行星架 Planet carrier

齿根过渡曲面 Fillet

圆环面的内圈 Inner circle of the

toroid

太阳轮 Sun gear

齿顶 Crest;Top land

啮合干涉 Meshing interference

内齿圈 Ring gear;Annulus gear

槽底 Bottom land

切齿干涉 Cutter interference

外齿轮 External gear

齿廓 Tooth profile

齿廓修型 Profile modification;

Profile correction 内齿轮 Internal gear

端面齿廓 Transverse profile

修缘 Tip relief

中心距 Centre distance

法向齿廓 Normal profile

修根 Root relief

轴交角 Shaft angle

轴向齿廓 Axial profile

齿向修形 Axial modification;Longitudinal correction

连心线 Line of centres

背锥齿廓 Back cone tooth profile

齿端修薄 End relief

减速齿轮副 Speed reducing gear pair 齿线 Tooth trace

鼓形修整 Crowning

增速齿轮副 Speed increasing gear pair 齿棱 Tip;Tooth tip

鼓形齿 Crowned teeth

齿数比 Gear ratio

模数 Module

挖根 Undercut

传动比 Transmission ratio

端面模数 Transverse module

瞬时轴 Instantaneous axis

轴平面 Axial plane

法向模数 Normal module

瞬时接触点 Point of contact

基准平面 Datum plane

轴向模数 Axial module

瞬时接触线 Line of contact

节平面 Pitch plane

径节 Diametral pitch

端面啮合线 Transverse path of contact

端平面 Transverse plane

齿数 Number of teeth

啮合曲面 Surface of action

法平面 Normal plane

当量齿数 Virtual number of teeth

啮合平面 Plane of action

分度曲面 Reference surface

头数 Number of starts;Number of threads

啮合区域 Zone of action

节曲面 Pitch surface

螺旋线 Helix;Circular helix

总作用弧 Total arc of transmission

齿顶曲面 Tip surface

圆锥螺旋线 Conical spiral

端面作用弧 Transverse arc of transmission

齿根曲面 Root surface

螺旋角 Helix angle;

Spiral angle

纵向作用弧 Overlap arc

基本齿廓 Basic tooth profile

导程 Lead

总作用角 Total angle of transmission 基本齿条 Basic rack

导程角 Lead angle

端面作用角 Transverse angle of transmission

产形齿条 Counterpart rack

阿基米德螺旋线 Archimedes spiral 纵向作用角 Overlap angle

产形齿轮 Generating gear of a gear 外摆线 Epicycloid

总重合度 Total contact ratio

产形齿面 Generating flank

长幅外摆线 Prolate epoicycloid

端面重合度 Transverse ratio

基准线 Datum line

短幅外摆线 Curtate epoicycloid

纵向重合度 Overlap ratio

轮齿 Gear teeth;Tooth

摆线 Cycloid

标准齿轮 Standard gears

齿槽 Tooth space

长幅摆线 Prolate cycloid

非变位齿轮 X-gero gear

右旋齿 Right-hand teeth

短幅摆线 Curtate cycloid

标准中心距 Referencr centre distance 左旋齿 Left-hand teeth

内摆线 Hypocycloid

名义中心距 Nominal centre distance

变位齿轮 Gears with addendum modification;

X-gears 直齿轮 Spur gear

分度圆柱面 Reference cylinder

高度变位圆柱齿轮副 X-gear pair with reference centre distance 斜齿轮 Helical gear;Single-helical gear

节圆柱面 Pitch cylinder

角度变位圆柱齿轮副 X-gear pair with modified centre distance

直齿条 Spur rack

基圆柱面 Basic cylinder

高度变位锥齿轮副 X-gear pair without shaft angle modification

斜齿条 Helical rack

齿顶圆柱面 Tip cylinder

角度变位圆柱齿轮副 X-gear pair with shaft angle modification

人字齿轮 Double-helical gear

齿根圆柱面 Root cylinder

变位系数 Modification coefficient

渐开线齿轮 Involute cylindrical gear 节点 Pitch point

变位量 Addendum modification

摆线齿轮 Cycloidal gear

节线 Pitch line

径向变位系数 Addendum modification coefficient

圆弧齿轮 Circular-arc gear;W-N gear 分度圆 Reference circle

中心距变位系数 Centre distance modification coefficient

双圆弧齿轮 Double-circular-arc gear 节圆 Pitch circle

圆柱齿轮 Cylindrical gear

假想曲面 Imaginary surfance

基圆 Basic circle

顶圆 Tip circle

任意点法向压力角 Normal pressure angle at a point

定位面 Locating face

根圆 Root circle

任意点端面压力角 Transverse pressure angle at a point

外锥距 Outer cone distance

齿距 Pitch

啮合角 Working pressure angle

内锥距 Inner cone distance

齿距角 Angular pitch

顶隙 Bottom clearance

中点锥距 Mean cone distance

公法线长度 Base tangent length

圆周侧隙 Circumferential blacklash 背锥距 Back cone distance

分度圆直径 Reference diameter

法向侧隙 Normal blacklash

安装距 Locating distance

节圆直径 Pitch diameter

径向侧隙 Radial blacklash

轮冠距 Tip distance;crown to back

基圆直径 Base diameter

锥齿轮 Bevel gear

冠顶距 Apex to crown

顶圆直径 Tip diameter

锥齿轮副 Bevel gear pair

偏置距 Offset

根圆直径 Root diameter

准双曲面齿轮副 Hypoid gear pair

齿线偏移量 Offset of tooth trace

齿根圆角半径 Fillet radius

准双曲面齿轮 Hypoid gear

分锥角 Reference cone angle

齿高 Tooth depth

冠轮 Crown gear

节锥角 Pitch cone angle

工作高度 Working depth

端面齿轮 Contrate gear

顶锥角 Tip angle

齿顶高 Addendum

直齿锥齿轮 Straight bevel gear

根锥角 Root angle

齿根高 Dedendum

斜齿锥齿轮 Skew bevel gear;

Helical bevel gear

背锥角 Back cone angle

弦齿高 Chordal height

曲面齿锥齿轮 Curved tooth bevel gear 齿顶角 Addendum angel

固定弦齿高 Constant chord height

弧齿锥齿轮 Spiral bevel gear 齿根角Dedendum angle

齿宽 Facewidth

摆线齿锥齿轮 Enicycloid bevel gear 任意点压力角 Pressure angle at a point 有效齿宽 Effective facewidth

零度齿锥齿轮 Zero T bevel gear

任意点螺旋角 Spiral angle at a point 端面齿厚 Transverse tooth thickness

圆柱齿轮端面齿轮副 Contrate gear pair 中点螺旋角 Mean spiral angle

法向齿厚 Normal tooth thickness

锥齿轮的当量圆柱齿轮 Virtual

cylindrical gear of bevel gear

大端螺旋角 Outer spiral angle

端面基圆齿厚 Transverse base thickness 8字啮合锥齿轮 Octoid gear

小端螺旋角 Inner spiral angle

法向基圆齿厚 Normal base thickness

圆柱齿弧锥齿轮 Spiral bevel gear with circle arc tooth profile

蜗杆 Worm

端面弦齿厚 Transverse chordal tooth thickness

分度圆锥面 Reference cone

蜗轮 Worm wheel

固定弦齿厚 Constant chord

节圆锥面 Pitch cone

蜗杆副 Worm gear pair

端面齿顶厚 Crest width

齿顶圆锥面 Face cone;tip cone

圆柱蜗杆 Cylindrical worm

法向齿顶厚 Normal crest width

齿根圆锥面 Root cone

圆柱蜗杆副 Cylindrical worm pair

端面齿槽宽 Transverse spacewidth

背锥面 Back cone

环面蜗杆 Enveloping worm

法向齿槽宽 Normal spacewidth

前锥面 Front cone

环面蜗杆副 Enveloping worm pair

齿厚半角 Tooth thickness half angle

中锥面 Middle cone

阿基米德蜗杆 Straight sided axial

worm;ZA-worm

槽宽半角 Spacewidth half angle

分锥顶点 Reference cone apex

渐开线蜗杆 Involute helicoid worm;

压力角 Pressure angle

轴线交点 Crossing point of axes

法向直廓蜗杆 Straight sided normal worm;

齿形角 Nominal pressure angle

齿根圆环面 Root tosoid

椭圆齿轮 Elliptical gear

咽喉面 Gorge

非圆齿轮副 Non-circular gear pair

平面蜗杆 Planar worm wheel;P-worm wheel

喉平面 Gorge plane

圆柱针轮副 Cylindsical lantern pinion and wheel

平面包络环面蜗杆 Planar double enveloping worm;TP-worm

喉圆 Gorge circle

针轮 Cylindsical tan tein gear ;pin-wheel

平面二次包络蜗杆 Planar double-enveloping worm wheel;TP-worm wheel 分度圆蜗旋线 Reference helix

谐波齿轮副 Harmoric gear drive

锥面包络环面蜗杆 Toroid enveloping worm wheel;TK-worm wheel

螺纹 Thread

波发生器 Wave generator

蜗杆齿宽 Worm facewidth

柔性齿轮 Flexspine

锥蜗杆 Spiroid

蜗轮齿宽 Worm wheel facewidth

刚性齿轮 Circular spline

锥蜗轮 Spiroid gear

直径系数 Diametral quotient

非圆齿轮 Non-circular gear

锥蜗杆副 Spiroid gear pair

咽喉半径 Gorge radius

分度圆环面 Reference tosoid

中平面 Mid-plane

齿宽角 Width angle